Bionoon 系列氮吹儀是采用微電腦處理和 PID 控制方式結合而形成的高精度溫度控制儀器 , 其工作原理是將氮氣快速、連續、可控地吹到加熱樣品表面，根據被濃縮溶劑的蒸發速度和沸點，設定加熱溫度，實現大量樣品的快速濃縮。本儀器采用鋁加熱模塊，其傳熱性好、傳熱均勻，這利于快速加熱和快速溫控。將氮氣吹到樣品表面，實現液體樣品的無氧濃縮.

Bionoon series nitrogen blowing instrument is a high-precision temperature control instrument formed by the combination of microcomputer processing and PID control mode. Its working principle is to blow nitrogen gas to the surface of the heated sample quickly, continuously and controllably, according to the evaporation speed of the concentrated solvent and Boiling point, set the heating temperature to achieve rapid concentration of a large number of samples. The instrument uses an aluminum heating module, which has good heat transfer and uniform heat transfer, can achieve rapid heating and rapid temperature control. Nitrogen is blown onto the surface of the sample to achieve anaerobic concentration of liquid samples

Bionoon-12DC 氮吹儀

Bionoon-12DC nitrogen blowing instrument

1.溫度范圍：室溫 +5℃ ~150℃  Temperature range: room temperature +5°C ~150°C
2.升溫時間：≤ 30min （從 20℃升至 150℃ )  Heating time: ≤ 30min (from 20°C to 150°C) 
3.溫度穩定性 @40℃：±0.3℃ Temperature stability @40°C: ±0.3°C
4.溫度穩定性 @100℃：±0.5℃Temperature stability @100°C: ±0.5°C
5.溫度穩定性 @120℃：±1℃ Temperature stability @120°C : ±1°C
6.放置模塊數量：1 塊  Place the number of modules: 1 block
7.定時時間設置：0~99h59min Timing time setting: 0~99h59min 
8.氮氣流量：0~10L/min Nitrogen flow: 0~10L/min
9.氮氣壓力：≤ 0.5MPa  Nitrogen pressure: ≤ 0.5MPa
10.材質：所有部件均為實驗室級，可耐受有機溶劑或選擇抗酸性涂層型，抗腐蝕 

Material: All parts are laboratory grade, that can withstand organic solvents or choose acid resistance Coating type, which is anti-corrosion 
11.模塊型號選擇：請參考官網介紹 Module model selection: please refer to the official website introduction

Bionoon-24DC 氮吹儀

Bionoon-24DC Nitrogen Blowing Apparatus

1.溫度范圍：室溫 +5℃ ~150℃  Temperature range: room temperature +5°C ~150°C
2.升溫時間：≤ 30min （從 20℃升至 150℃ )  Heating time: ≤ 30min (from 20°C to 150°C) 
3.溫度穩定性 @40℃：±0.3℃ Temperature stability @40°C: ±0.3°C
4.溫度穩定性 @100℃：±0.5℃ Temperature stability @100°C: ±0.5°C
5.溫度穩定性 @120℃：±1℃ Temperature stability @120°C : ±1°C
6.放置模塊數量：2 塊  Place the number of modules: 2 
7.定時時間設置：0~99h59min Timing time setting: 0~99h59min 
8.氮氣流量：0~10L/min Nitrogen flow: 0~10L/min
9.氮氣壓力：≤ 0.5MPa  Nitrogen pressure: ≤ 0.5MPa 
10.材質：所有部件均為實驗室級，可耐受有機溶劑或選擇抗酸性涂層型，抗腐蝕 ;

Material: All parts are laboratory grade, that can withstand organic solvents or choose acid resistance Coating type, which is anti-corrosion
11.模塊型號選擇：請參考官網介紹 module model selection: please refer to the official website introduction

產品特色  Feature of product

1.氣針相互獨立，不會引起交叉污染。

The gas needles are independent of each other and will not cause cross contamination.  
2.每個氣針流量大小可單獨調整。 

 The flow rate of each air needle can be adjusted individually. 
3.各吹管通道可組合使用或單獨使用。 

Each blowpipe channel can be used in combination or alone. 
4.每個氣針流量調節閥和模塊孔位垂直對應，調整直觀、方便。

Each air needle flow regulating valve is vertically corresponding to the hole position of the module, so that the adjustment is intuitive and convenient.

5.系統控溫精度高、控溫范圍廣、溫度校準方便。 

The system has high temperature control precision, wide temperature control range and convenient temperature calibration. 
6.升降機構有安全保護裝置，使用安全。 

The lifting mechanism has a safety protection device, which is safe to use. 
7.升降機構帶刻度顯示，定位準確明了。

The lifting mechanism has a scale display, and the positioning is accurate and clear.